Volvo RWD 120-130 Forum

INDEX FOR 10/2025(CURRENT) INDEX FOR 1/2005 120-130 INDEX

[<<]  [>>]


THREADED THREADED EXPANDED FLAT PRINT ALL
MESSAGES IN THIS THREAD




  REPLY TO THIS MESSAGE    PRINT   SAVE 

clutch release bearing 120-130

posted by  voice122 on  Wed Apr 5 21:30 CST 2023
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Oct 20 00:08 CST 2014
[RELATED]

Hello all

I am fitting a M310 to my B20 with a sachs pressure plate

Can any one advise the part # of the release bearing to use with clutch fork part

# 1212189

Thanks in advance

David








  REPLY TO THIS MESSAGE    PRINT   SAVE 

clutch release bearing 120-130

posted by  planetman on  Thu Apr 6 09:47 CST 2023
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Fri Oct 24 09:29 CST 2014
[RELATED]

The latest part number is 3549881.

What year 122?
--
Eric
Hi Performance Automotive Service (formerly OVO or Old Volvos Only)
Torrance, CA 90502
hiperformanceautoservice.com or oldvolvosonly.com








  REPLY TO THIS MESSAGE    PRINT   SAVE 

clutch release bearing 120-130

posted by  voice122 on  Thu Apr 6 23:07 CST 2023
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Oct 20 00:08 CST 2014
[RELATED]

Hi Eric

Its a 1968 but i have a B20E block in the car

Regards David








  REPLY TO THIS MESSAGE    PRINT   SAVE 

clutch release bearing 120-130

posted by  voice122 on  Thu Apr 6 23:18 CST 2023
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Oct 20 00:08 CST 2014
[RELATED]

The problem i have is with the clutch fork pivot point at the end of the fork i was unable to get the clutch to release
some where in the recesses of my mind i think i used a 672122 bearing in the past and then i read that it would not work with a sachs pressure plate and now i doubt myself
any experience i would like to know
Thanks David








  REPLY TO THIS MESSAGE    PRINT   SAVE 

clutch release bearing 120-130

posted by  derek uk on  Fri Apr 7 05:44 CST 2023
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Fri Oct 24 12:33 CST 2014
[RELATED]

There are 3 different heights of release bearing. Always best to get a 3 piece clutch set to make sure you get the correct one. A properly matched set will fit either a hydraulic or cable set up. Wrong release bearing and you will be having it all to pieces again. Been there, or least my garage has!








  REPLY TO THIS MESSAGE    PRINT   SAVE 

clutch release bearing 120-130

posted by  planetman on  Thu Apr 6 23:29 CST 2023
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Fri Oct 24 09:29 CST 2014
[RELATED]

The 672122 is used with a Borg & Beck(B&B) clutch and not a Fitchel & Sachs(F&S).

How are you actuating the clutch? A 1968 122 would have come with a hydraulically operated clutch and the M410 for a 4 cylinder used a cable clutch.
--
Eric
Hi Performance Automotive Service (formerly OVO or Old Volvos Only)
Torrance, CA 90502
hiperformanceautoservice.com or oldvolvosonly.com







<< < > >>



©Jarrod Stenberg 1997-2022. All material except where indicated.


All participants agree to these terms.

Brickboard.com is not affiliated with nor sponsored by AB Volvo, Volvo Car Corporation, Volvo Cars of North America, Inc. or Ford Motor Company. Brickboard.com is a Volvo owner/enthusiast site, similar to a club, and does not intend to pose as an official Volvo site. The official Volvo site can be found here.