740 Steering wheel tool, #998 8695
740 Strut holder hook tool #5045
740 Strut tool bushing drift #2704
740 Control Arm Ball Joint Press # 5259
740 Control Arm Bushing Press out # 5091, 5240
740 Control Arm Bushing Press in # 2904
740 Track Rod tools in/out bushings# 2731, 2733; 2706


Automatic trans drive flange holder and seal driver # 5075 and # 5149.

Brake tool # 2919 piston chamfer tilter, to stop squealing
Brake tool # 2918 for 20 degree tilt

Cam & Intermediate shaft sprocket holder, #5034
Cam and Intermediate shaft, Seal driver # 5025

Clutch Alignment tool, # 5111

Control Arm (740) - # 5356, 5359, 5078
Control Arm tool, to remove & install Front control arm bushing, # 5084, # 5085, # 5091
Control Arm tool, to remove & install Rear control arm bushing, # 5082, # 5083, # 1801

Crank Pulley holder # 5284
Crank Seal Intstaller # 5283

Engine Stand and fixture, # 2520 & 5297
Engine Rear Oil Seal tools #5276, # 1801
Engine Removal Install Lifting Sling & Yoke, # 2810 & # 5035
Engine Holding tools, for oil pan/motor mounts, # 5006, 5115, 5035 (2x5003?), 5871

FI pressure tester # 5011, #5228, #5229

Flywheel locking tool # 5112


Ignition switch/steering # 5294, #5295 to press out lock

Man.Trans, 5th gear tools: #"s 5986; 5973; 998-7693; 5262; 5305; 2985; 5058; 5148; 5147
Manual trans oil filter and check valve remover and installer, etc. #2836

Pressure Gauge, # 2834

Rear axle puller and bearing puller # 2709
Rear axle puller for flange # 2261
Rear axle seal puller # 5069

Shock Absorber holder and Strut loosening tool # 5036, # 5037

Steering arm, to press rod out of # 5043

Strut camber adj tool # 5038
Strut tools for front cartridge # 5039, # 5046, # 5303

Suspension, Rear torque arm bushing tool # 5086, # 5087
Suspension, Rear track rod bushing tools # 2731, # 2733, # 2706
Suspension, Rear Trailing Arm bushing, #5078, #5079
Suspension, Front Trailing Arm bushing, # 5087, #5088

Transmission, manual trans pilot bearing remover # 4090
Transmission, manual trans pilot bearing installer # 1426
Transmission support for install and removal # 5972

Trunk lid tool - to remove & install sedan lid gas shock, # 2744, # 5211

Valve guide press out tool # 5218
Valve guide reaming tool # 5224
Valve clearance measuring tool # 5222
Valve compressor, Intake & exhaust # 5022
Valve disc remover # 5026

Wheel tool - to press out wheel studs # 2862
Wheel tool - to remove front wheel hub # 2722


thank you all,
diyer

Hmmmmm. Are you making out your Christmas wish list?
--
-------Robert, '93 940t, '90 240 wagon, '84 240 diesel (she's sick) , '80 245 diesel

None, except the 240 rear trailng arm bushing tool, and even then you can make your own.
--
Jim McDonald

I don't understand your reasoning. Just want to have on hand what I will need to have to restore these model cars. As many problems as I encounter with [Volvos] I figure I might as well have them on hand. I know some will not be needed, but I also bet that if I asked this question of Volvo techs, I bet they would have a different view about working frustrated. Sure, you can take a car apart with a crescent wrench but who the heck would want to! Btw, I saw the cryptic description of making that tool and that would cost me more time and labor than to just buy the dammed thing from Volvo. Don't you think Volvo has knows that?

diyer

Your joking, right? Well, probably not, so, why do you say none are needed?

Seriously,
diyer